Supergoodsales Motor Controller 12V 24V 48V Forward Reverse Brushless PWM DC Electric Speed Module 400W
————–☀Welcome to Supergoodsales☀————-
✔Good Quality✔Available✔Lowest Price
✈Shipping from oversea,items will arrive your home in 1-2 week.
⏩If you follow us and screenshot to us, you will have a free gift.
❀Please Enjoy Your Shopping Time↖(^ω^)↗
1. Humanized design, the interface uses a terminal, a standard heat sink, and an integrated speed potentiometer on the board
2. Full chip technology, stable performance, with forward and reverse, brake function, motor speed controller adopts Hall brushless controller
3. Wide voltage 6‑60V high power 400W DC three‑phase brushless with Hall controller
4. Support PLC 0‑5V analog control, support PWM to 0‑5V control, can be used when power is on, saving time and effort
5. There are three relatively thick phase wires on the machine, and there are also three phase wire interfaces on the drive board, which are marked MA, MB, MC, etc.
Specification:
Item Type: Motor Controller
Material: PCB
Purpose: Motor Controller
Working Voltage: 6-60V
Maximum Current: Rated 16A Maximum 20A
Maximum Power: 400W
Overcurrent Protection: Yes
How to Use:
Interface Description:
1. MA MB MC phase line output is connected to the motor
2.5V GND The motherboard comes with 5V power supply (external power supply is available, the current does not exceed 50MA)
3. VCC GND main power supply (external DC power supply)
4. SC speed pulse signal output (only the interface is reserved, no technical support)
5. DIR direction control, forward and reverse control interface (low level is effective, can be connected to the ground external switch)
6. STOP Stop stop control interface (low level is effective and can be connected to the ground external switch)
7. BRAKE brake control brake control interface (high level is effective, 5V external switch can be connected)
8. Speed Control speed control signal input (onboard integrated potentiometer speed control can also be connected with 0‑5V analog quantity PWM dual signal input speed control)
9.Ha Hb Hc +5V GND Hall signal power supply input interface, generally the motor with Hall has 5 corresponding wires
Package List:
1 x Motor Controller
1 x Terminal Line
Note:
1. This drive is a DC three‑phase brushless control board, which requires the motor to have a Hall to work normally
2. This drive is only suitable for DC brushless and Hall motors with an electrical angle of 120°
3. When the PWM signal is input from the 2 ports of the motherboard P G (the built‑in potentiometer on the board is adjusted to the minimum, and the short interface on the board is shorted at the same time, the wiring is shown in the figure above), the amplitude is 2.5‑5V, and the frequency is 50HZ‑20KHZ.
4. When the external analog 0‑5V input, input from the 2 terminal ports of the main board (the potentiometer on the board is adjusted to the minimum, the wiring is shown by the dotted line in the figure above)
5. When the external potentiometer is used to adjust the speed, connect it to the 3 terminal ports of the main board (the potentiometer on the board is adjusted to the minimum, and the wiring is indicated by the potentiometer on the picture)
6. The forward and reverse rotation and stop are grounded through a switch (0 potential). The low level is valid, and the external MCU can also give a low level signal. The brake is connected to a 5V high‑level effective through a switch. The front row of wiring terminals are all weak current signals directly input to the MCU main control, and cannot be touched or touched with high voltage and strong current.
7. When the PWM signal is input from the 2 ports of the motherboard PG (the built‑in potentiometer on the board is adjusted to the minimum, and the short interface on the board is short‑circuited at the same time as shown in the figure above), the amplitude is 2.5‑5V, and the frequency is 50HZ‑20KHZ.
8. When the external analog 0‑5V input, input from the 2 terminal ports of the main board (the potentiometer on the board is adjusted to the minimum, the wiring is shown by the dotted line in the figure above)
9. Plea
